On this tutorial, I’ll information you thru establishing the DJI O4 Air Unit Professional in your FPV drone. This consists of connecting the wiring to the flight controller, configuring Betaflight, and sharing helpful suggestions and finest settings to get the optimum efficiency on your particular wants.
Nonetheless debating whether or not it’s best to get the DJI O4 Professional? Try my evaluation: https://oscarliang.com/dji-o4-air-unit-pro/
The place to Purchase?
You should buy the DJI O4 Air Unit Professional on the following retailers:
The entire O4 Professional bundle, together with the digital camera and antenna, retails for US$229. Particular person spare elements can be bought individually, permitting you to exchange broken elements with out shopping for a brand new unit:
Connecting O4 Professional to FC
The DJI O4 Air Unit Professional makes use of the identical 6-pin connector and pinout because the O3, making it plug-and-play with flight controllers designed for present DJI Air Models.
Pinout of the 6-pin connector:
- VCC: Energy provide
- GND: Floor
- RX/TX: Required for OSD and telemetry (e.g., displaying battery voltage)
- GND and SBUS: For DJI Distant Controller (elective)
If you’re not utilizing a DJI Distant to manage the drone, and are as an alternative utilizing your individual radio receiver, it’s beneficial to take away the SBUS wire (DJI HDL) from the connector. This will stop potential conflicts. Use a pointy device, comparable to a needle, to elevate the tab within the connector and pull the wire out. On this case you may additionally take away the extra floor wire (brown).
Powering the O4 Professional
The O4 Professional might be powered instantly from a 2S to 6S LiPo battery (7.4–26.4V). Nonetheless, every time potential, energy it through a 9V BEC on the flight controller for added safety in opposition to voltage spikes.
Energy necessities:
- Max energy consumption: ~10.5W
- Present draw: 1.15A at 9V
- Advisable BEC: Rated for at the very least 1.5A at 9V
Disconnecting Digicam and Antenna
It’s potential to disconnect the digital camera or antenna if it makes set up simpler.
Loosen the 4 M2 screws on the corners of the Air Unit.
Fastidiously elevate the underside plate with out pulling on the ribbon cable. Disconnect the UFL connectors for the antenna and digital camera.
Mounting Digicam and Air Unit in Body
When mounting the Air Unit, make sure the DJI emblem is going through up. Use M2 screws to safe the transmission module.
Activation
As soon as the O4 Professional is related to the flight controller (FC), it’s time to activate it. If the Air Unit has been beforehand activated, this step isn’t required.
Obtain DJI Assistant 2 (Client Drone Sequence): https://www.dji.com/nl/downloads/softwares/dji-assistant-2-consumer-drones-series.
When you’ve got beforehand put in it, it’s a good suggestion to obtain and set up the newest model. Be aware: Activation can’t be performed through the DJI Fly App.
Necessary: The O4 Air Unit have to be powered by a battery or a appropriately rated energy provide throughout activation. In contrast to the O3, it can’t be activated utilizing simply the USB-C cable. Though the USB-C cable isn’t included, any USB-C information cable will work.
Firmware Replace
Whereas related to DJI Assistant 2, examine if new firmware is offered on your O4.
Professional Tip: For firmware updates, you may unplug the battery in the course of the course of to keep away from heating.
Pairing DJI Goggles 3 with O4 Air Unit Professional
Earlier than pairing, guarantee your Goggles 3 firmware is up to date to the newest model. With out this replace, the O4 Professional and O4 choices won’t seem within the menu. Observe these steps:
Replace Firmware
- Activate the Goggles 3 and join them to your laptop utilizing a USB-C information cable.
- Replace the firmware through DJI Assistant 2.
Professional Tip: If the Goggles 3 doesn’t seem in DJI Assistant 2, navigate to the goggles menu:
Settings → About → OTG Wired Connection and allow it.
Choose O4 Air Unit Professional within the Goggles Menu
- Go to the goggles menu, navigate to Standing → Swap, and choose “DJI O4 Air Unit Professional.”
Enter Bind Mode
- Press and maintain the ability button on the goggles till they begin beeping, indicating they’re in bind mode.
Energy on the O4 Air Unit
- Await the LED on the Air Unit to show purple.
- Use tweezers to press the bind button on the Air Unit. The purple LED will start flashing slowly, indicating it’s in bind mode.
Full Binding
- Binding is profitable when the LED on the Air Unit turns strong inexperienced, and the goggles show the digital camera feed.
Pairing Goggles 2/Integra with O4 Professional
To make use of the O4 Air Unit with Goggles 2 (or Integra), you’ll have to replace the firmware on each gadgets. And don’t fear, you’ll nonetheless get compatibility with the O3 Air Unit, in addition to older DJI FPV Air Models and the Vista system.
Professional Tip: In the event you’re utilizing a Mac and encounter connection points (e.g., Goggles 2 not showing in DJI Assistant 2), it is a identified downside. Sadly, there isn’t a dependable repair. A workaround is to replace utilizing the DJI Fly App in your smartphone or change to a Home windows PC for the firmware replace.
After the replace, go to the goggles menu and choose both O4 Air Unit or O3 Air Unit underneath the settings.
Press the hyperlink button between the lenses on the Goggles 2 to enter bind mode.
Energy on the O4 Air Unit and await the LED to turn into purple. Press the bind button on the Air Unit (e.g., utilizing tweezers). The purple LED will flash, indicating bind mode. Binding is profitable when the LED turns strong inexperienced, and the digital camera feed seems in your goggles.
Switching Between Professional and Lite
In the event you use each the O4 Professional and O4 Lite, keep in mind to modify between them within the goggles menu earlier than flying. Every time you fly with a distinct unit, you’ll have to manually choose the corresponding Air Unit within the goggles settings.
Unlock FCC Mode
In case your Goggles 3 are shipped with CE mode (to adjust to European rules), they are going to be restricted by way of output energy (solely 25mW) and channels. There can be just one accessible channel within the 40MHz mode and three accessible channels within the 20MHz mode.
In FCC mode, it’s best to have the utmost 1200mW output energy possibility, and there needs to be 7 accessible channels within the 20MHz mode, and three accessible channels within the 40MHz and 60MHz mode.
For goggles in CE mode, it’s potential to carry out the “FCC hack” to unlock larger output energy (extra vary and sign penetration) and extra channels (permits extra pilots within the air on the similar time), however solely do that if it’s authorized the place you fly.
To change to FCC mode, merely get the file “ham_cfg_support”, unzip it to the basis listing of the SD card and put it within the goggles, energy on goggles, that’s it.
Obtain file right here: https://drive.google.com/file/d/1ug2U_i5kdrKQQ2I17NLJBXm2tKQeNj5Q/view?usp=share_link
To examine if you’re in FCC mode, go to Settings => Transmission => Channel Mode, change to Guide, underneath 40MHz or 60MHz bandwidth, it’s best to see 3 channels accessible in FCC mode. If it is going to solely present 1 channel there, you’re in CE mode.
As soon as FCC mode is unlocked, you received’t should do it once more. You possibly can return to CE mode by manufacturing unit reset the goggles (within the menu Settings => About).
Setup OSD in Betaflight
The DJI O4 Air Unit absolutely helps the Betaflight OSD, together with the Betaflight OSD menu and all accessible OSD components.
Go to the Presets tab, and seek for “dji”, the “FPV.WTF MSP-OSD” preset ought to pop up. In choices, choose the UART you have got related to the O4 Professional Air Unit.
To allow HD OSD, go to the settings menu within the goggles, Settings > Show > Canvas Mode, and choose HD OSD.
This lets you show the OSD with smaller fonts and drag OSD components all the way in which to the perimeters of the display. If you choose Regular Mode, the font will seem a lot bigger.
Lastly, go to the OSD tab in Betaflight Configurator. Beneath Video Format, guarantee HD is chosen.
Setup DJI Distant Controller
In the event you’re utilizing a third-party radio hyperlink, you may skip this part.
Utilizing DJI’s distant controller eliminates the necessity to wire a separate radio receiver to the flight controller, because the DJI O4 Air Unit additionally serves as an RC hyperlink. This simplifies the setup course of. Nonetheless, there are a number of downsides to think about:
- Fundamental performance: DJI’s distant controllers lack the superior options and management precision supplied by extra refined programs like ExpressLRS.
- Failsafe dependency: Because the video and radio alerts share the identical hyperlink, dropping the video sign additionally ends in a failsafe, which isn’t the case with superior RC hyperlinks like ExpressLRS that sometimes outperform video hyperlinks considerably.
Suitable DJI Distant Controllers:
- RC2: Works solely with the Goggles 2 and Integra.
- RC3: Works solely with the Goggles 3 and N3.
Pairing the DJI Distant Controller 3:
- Energy in your goggles 3 and RC3.
- Lengthy-press the energy button on each the goggles and distant controller to enter linking mode.
- As soon as the gadgets are efficiently linked:
- The goggles will cease beeping and show the reside view.
- The distant controller will cease beeping.
Configuring Betaflight:
- Within the Ports tab, allow Serial RX for the UART related to the SBUS wire.
- Within the Receiver tab, set the protocol to SBUS (through UART).
Movies Recording
To start out recording utilizing the goggles, swipe down from the highest to entry the Report button within the on-screen menu. Alternatively, you may configure the goggles and the O4 Air Unit (AU) to begin recording routinely if you arm the quad. Navigate to Settings → Digicam → Superior Digicam Settings to allow this selection, which many pilots discover extra handy.
Chances are you’ll discover the video recordsdata get break up within the O4 when it will get to about 4GB. That is as a result of FAT32 format of the SD card, which has a 4GB file dimension restrict. There isn’t any work round to this until you document at a decrease decision or body price which ends up in smaller file dimension.
Nonetheless, right here’s the silver lining. When these break up recordsdata are imported right into a video editor sequentially, they need to play again seamlessly. There shouldn’t be any skips, stutters, or overlaps. It implies that whilst you might need a number of recordsdata for a single recording session, your closing edited video can nonetheless be one easy, steady clip.
If that you must stablize these movies in Gyroflow, this system truly permits you to import these clips first earlier than making use of stabilization to make sure consistency.
Video bitrates underneath completely different decision/body price:
- 4K 60fps: 130Mbps
- 4K 50fps: 120Mbps
- 4K 30fps: 90Mbps
- 2.7K 60fps: 100Mbps
- 2.7K 50fps: 90Mbps
- 2.7K 30fps: 70Mbps
- 1080p 120fps: 80Mbps
- 1080p 100fps: 70Mbps
- 1080p 60fps: 50Mbps
- 1080p 50fps: 40Mbps
- 1080p 30fps: 25Mbps
Obtain Video
To obtain movies, plug within the USB cable. There’s no have to take away the SD card. For the O4 AU, you’ll see two separate exterior drives—one for the SD card and one for the interior reminiscence. To obtain video off the Goggles, it’s best to energy them on first, in any other case connecting the USB cable does nothing.
In the event you plan to document movies instantly on the O4 Air Unit, you may wish to get a micro SD card for expanded storage. Be aware that not all SD playing cards are appropriate. For instance, I encountered a gradual SD card warning with the Sandisk Excessive Professional 64GB U3 A1 card. Switching to a Samsung 256GB Evo A2 resolved this problem. You will discover that card right here: https://amzn.to/3B8JplQ
For finest efficiency, format the SD card contained in the Air Unit utilizing the Format possibility within the goggles’ digital camera menu.
Video Stabilization
The O4 Air Unit helps two stabilization strategies: Rocksteady and Gyroflow.
Rocksteady is built-in and might be enabled within the goggles’ menu. It stabilizes your footage routinely throughout recording, providing outcomes which are ok for many customers. To make use of Rocksteady, set Recording Stabilization to On.
Gyroflow is a free software-based stabilization device. It gives extra flexibility, permitting you to fine-tune stabilization ranges to satisfy your preferences. With Gyroflow, the uncooked footage stays unstabilized, and also you resolve how a lot stabilization to use throughout post-processing.
To make use of Rocksteady, merely set Recording Stabilization to On.
If you wish to use Gyroflow and take advantage of out of it, set
- Side Ratio: 4:3
- Digicam FOV: Broad
- Recording Stabilization: OFF
To make use of Gyroflow, that you must obtain it, which is free. You simply want to pull and drop your footage within the software program and the stabilized footage able to be exported. You possibly can wonderful tune the stabilization settings, which I defined in my Gyroflow tutorial: https://oscarliang.com/gyroflow/
Easy methods to Keep away from Jello and Vibration
The O4 digital camera is extremely delicate to vibrations, making it essential to isolate the digital camera from vibration sources or eradicate vibrations altogether.
Keep away from utilizing a 24kHz PWM frequency in your ESC. Just like the O3, the O4 performs poorly with low ESC PWM frequencies as a consequence of elevated vibration and noise. Utilizing a better frequency, comparable to 48kHz, is beneficial for optimum stabilization efficiency.
Mounting the O4 digital camera instantly on carbon fiber or CNC aluminum isn’t advisable, as vibrations can switch instantly from the motors to the digital camera, resulting in jello results in your footage. As a substitute, mount the digital camera on a tender materials that gives vibration dampening.
Many trendy frames come geared up with silicone or rubber inserts or spacers particularly designed for mounting FPV cameras, which may cut back vibrations. These supplies act as a buffer, stopping direct transmission of motor-induced vibrations to the digital camera, thus enhancing video readability and decreasing jello.
Finest O4 Professional Settings
Advisable Digicam Settings for the Finest FPV Expertise (For many who prioritize low latency and don’t care a lot about recording high quality):
- Side Ratio 4:3
- Video High quality: 1080p 100fps (affords lowest latency)
- Digicam FOV: Broad
- Auto ISO Restrict: 6400
- Coloration: Regular
- Auto Mode
Advisable Digicam Settings for the Finest HD Recording (For these Utilizing ND filter, Gyroflow stabilization, and Coloration grading):
- Side Ratio 4:3
- Video High quality: 4K 60fps (30fps is likely to be higher for low mild, however it may well improve latency, making correct flying more durable.)
- Digicam FOV: Broad
- Recording Stabilization: OFF
- Coloration: D-Log M
- Sharpness: -1 (you may improve sharpness in post-editing if wanted)
- Noise Discount: 0 (or +1 in low-light conditions to cut back noise in darkish areas)
- Digicam Mode: Guide
- Shutter Velocity: 1/120
- Auto ISO
- Auto ISO Restrict: 200 – (set this as little as potential to keep away from graininess; nevertheless, too low may make the picture too darkish.)
- White Steadiness: Put White Steadiness on Auto first and see what the system select, then lock in with that worth, so WB is fastened throughout flight
- Show Help: On (restores distinction and saturation within the goggles feed when utilizing D-Log M however doesn’t have an effect on recorded footage.)
Advisable Digicam Settings for Respectable HD Recording (For many who desire little to no enhancing):
- Side Ratio 4:3
- Video High quality: 4K 60fps
- Digicam FOV: Broad
- Auto ISO Restrict: Set as little as potential on your lighting situations. If not sure, depart it on the default (6400). Be aware that larger ISO could result in grainier photographs in darkish areas, nevertheless it ensures visibility.
- Recording Stabilization: ON
- Coloration: Regular
- Digicam Mode: Auto
- White Steadiness: Auto
Advisable Transmission Settings for Solo Flying
- Race Mode: OFF
- Transmission Energy: Use the very best energy stage legally allowed, or set it to Auto.
- Channel Mode: Guide
- Bandwidth: 60MHz (60mbps bitrate)
Advisable Transmission Settings When Flying with Different Pilots
- When flying with different DJI pilots: Contemplate decreasing transmission energy and utilizing smaller bandwidth.
- When flying with pilots utilizing different FPV programs (e.g., Analog, HDZero): Allow Race Mode to cut back interference.
Race Mode
Race Mode is a function designed particularly for FPV racing, accessible solely on the DJI Goggles 3 and N3, however not on the Goggles 2 and Integra as a consequence of {hardware} limitations. It optimizes the system for low-latency efficiency and minimizes interference in race environments by aligning its channel frequencies to Race band. Right here’s what Race Mode affords:
- Lowest Latency: Race Mode forces the system into 100fps with a 20MHz bandwidth, reaching latency as little as 20ms.
- Channel Alignment: Channels align with commonplace race band frequencies, making it extra appropriate with different FPV programs.
- Cleaner Sign: The telemetry hyperlink now operates on the identical static frequency because the video sign, decreasing interference with different pilots. When the Air Unit is off, the goggles cease transmitting altogether, permitting pilots to stroll round with out affecting others.
- Commerce-offs: Narrower bandwidth and decrease energy output cut back vary and penetration, making it unsuitable for freestyle, cinematic, or long-range flying. Nonetheless, these limitations are acceptable for racing, which generally happens in open fields.
Warning: Keep away from powering in your Air Unit whereas others are within the air, because it momentarily sweeps throughout the band, probably inflicting interference for individuals who are nonetheless within the air. For all different kinds of flying, regular mode affords higher RF efficiency.
Transmission Energy Superb Tune
This function permits you to fine-tune the output energy of your VTX by ±1mW to ±7mW to make sure compliance with racing occasion rules. For many customers, this setting isn’t obligatory until you’re attending a regulated racing occasion the place exact energy ranges are required.
Spectator Mode
The Spectator Mode allows you to watch different pilots flying with the O4 Air Unit, nevertheless it comes with compatibility limitations:
- Goggles 3 and N3 customers can solely spectate different pilots utilizing G3 and N3.
- Goggles 2 and Integra can solely spectate different pilots utilizing G2 and Integra.
Spectator Mode doesn’t work throughout these two generations, so make sure you’re utilizing the identical era goggles because the pilot you wish to spectate.
Changing Digicam and Antenna
The O4 Professional is modular, which means its digital camera and antenna might be changed simply. Disassembly is simple, making it handy for repairs or upgrades.
Whereas the O4 Professional and O4 Lite digital camera cables are bodily the identical, the cameras are not interchangeable—for those who swap them, no picture will show. The O3 digital camera is not appropriate in any respect with both the O4 Professional or O4 Lite.
In the event you want an extended digital camera cable for the O4 Lite, you need to use the cable from the O4 Professional, as they’re interchangeable in size.
Conclusion: Setting Up the DJI O4 Professional Air Unit
The DJI O4 Professional Air Unit is a cutting-edge FPV system that brings unbelievable video high quality, dependable transmission, and superior options to your FPV drones. Whereas the setup course of could seem intricate at first, this information simplifies every part from wiring and pairing to fine-tuning settings for optimum efficiency.
By following this information, you’ll not solely get your O4 Professional Air Unit up and operating easily but in addition be geared up with suggestions and tips to optimize its efficiency. Now, you’re able to get pleasure from crystal-clear footage, seamless transmission, and an enhanced FPV expertise. Fly secure, and have enjoyable exploring what the O4 Professional can do!
